2020
Purchase, installation and launch of a hot melt adhesive production line. Purchase, installation and launch of a coarse-type drawing section for the production of wire and mono-cores and TPZh, both copper and aluminum. Mass release of RG 6.
2020
2019 -2020
Strengthening the drawing area, as well as replacing the drawing machine. Category 6 LAN cable mass production. An additional torch-type stranding machine was purchased. This made it possible to exclude the process of stranding by contractors, as well as the logistics operations associated with this process. By 2020, a full cycle of wire production has been established. The production of fundamentally new types of products SIP4, AVVG, VVG cables and PVA wires of large sections has been mastered.
2019 -2020
2018-2019
Upgraded extrusion line for sheathing, thereby increasing production capacity by 40%. The range of products has been expanded: the production of high-strength flexible cables has been mastered and the line has been expanded. Purchase, installation and launch of additional equipment for braiding, thanks to which the technology for the production of coaxial cables has been mastered. A pilot batch of coaxial cable (RG 6) was released.
2018-2019
2018
The mass production of heating (heating) cables has been launched. Development and release of a pilot batch of self-regulating heating cable. Production of construction cables under the Epicenter trademark (TM Expert).
2018
2016-2017
Renovation of equipment for applying insulation. Introduction of a new surface coating technology that increases productivity and uses raw materials carefully. Production of a pilot batch of Category 6 LAN cable.
2016-2017
2015-2016
Mastering the production of dyes (masterbatches, masterbatches) for PVC, PE, TPE and universal. Start of development and production of pilot batches of heating (heating) cables.
2015-2016
2015
Mastering the production of communication cables. Production of pilot batches of wires of the type:
  • Single-pair PRPPM, PRPPM
  • Multi-pair CCIEP
  • Interstation KSPP
  • Cross station wire PKSV J-Y (ST) Y
2015
2013-2014
Modernization and expansion of production capacities of PVC and TPE production workshops. Increase in production of construction wires. The production of cables for signaling type Alarm has been established.
2013-2014
2012-2013
Launch of a site for the production of thermoplastic elastomers (TPE) for flexible cables (CG), as well as general-purpose thermoplastic elastomers, for example, for wear-resistant car mats.
2012-2013
2012
Production of LAN cables for outdoor use in a polyethylene sheath (PE) with a supporting element (wire or cable) and without a supporting element. Strengthening of the drawing area, two additional drawing machines were purchased.
2012
2011-2012
Development of flexible cables (CG) using imported thermoplastic elastomer for sheath production. Start of development of our own cable thermoplastic elastomer. Purchase of new equipment for the production of LAN cables. The first samples of the twisted pair UTP FTP cat. 5e PVC coated
2011-2012
2009-2010
Mastering a new type of wires: Sound. Thanks to the development of the production of transparent PVC.
2009-2010
2008
Start of PVC production. Renovation of drawing, twisting and extrusion equipment.
2008
2005
Launch of the third extrusion line for the production of construction cords and heavy-gauge wires, maximum diameter 90 mm.
2005
2004-2005
The second extrusion line was launched. A production site for twisting thin wires into a flexible core was launched. A full cycle of vein production has been established, thanks to the launch of a copper wire production site. The beginning of the development of the production of construction cords and wires, for example, PVA and SHVVP.
2004-2005
2004
The beginning of the manufacture of automotive cords and wires for the production and supply of harnesses to AvtoZAZ.
2004